Enter new User Access Code: are not suitable for plasterboard walls, if mounting the Keypad onto plasterboard use appropriate wall plugs. Page Testing The Keypad 7. Fix the rear cover to the wall using the two 18mm would cut across the fan detection pattern. PIR No. Page Magnetic Contact Detectors House Code and are mounted within The detector should be mounted on the fixed effective radio range of the Solar Siren. Replace the battery cover on the detector. Page Testing The System Disarm the system from outside the property.
Disarm the system and stop the Siren by pressing Delay-Arm mode will arm the system with a 15 second button on the Remote Control. Page Alarm Record 4. Ensure detector is within effective radio range of 2. Ensure battery holder connections are making Siren and equipment is not mounted close to good contact with the battery. Battery low - replace battery. Page Extending Your Alarm System i.
Low battery - replace battery. Page 23 A full description of the fault. All relevant batteries disconnected. Note: If returning a Solar Siren, make sure that both the rechargeable battery and initial power up battery are disconnected and secure. This manual is also suitable for: Sa2 Sac1. Print page 1 Print document 24 pages. Rename the bookmark. Delete bookmark? Cancel Delete. Repeat this for the remaining numbers. Suggested resolution: Press number 8 on the keypad and then press the up arrow 5 times, press the down arrow 6 times and then press enter and escape twice on the keypad.
This will stop the beeping and, in some cases, extinguish the memory light. If the memory light does not extinguish then the following sequence should be followed:. Press number 4, enter your access code and press enter. This will play any messages that are stored, these will need to be cleared, press button 1, it will ask for confirmation to confirm this press key 1 again and it will delete that message.
Repeat this sequence until all messages are deleted and press escape twice to exit. If the above procedure does not clear the memory light, then arm and disarm the system and try the sequence again. In the event that it has still not cleared then advise to reset factory settings.
Suggested resolution: Replace all PIR detector and magnetic batteries and then press escape twice on the keypad to extinguish the battery light and return to a disarmed mode. Suggested resolution: Control unit constantly bleeping every 30 seconds? Is jamming detection activated? If so, disable this function on the control panel. If you are still struggle give one our customer support team a call.
Answer: Set main configuration switch to C. Set the house code but do not connect jamming detection link, connect both batteries, press down the tamper switch and hold closed. Keeping the tamper switch closed press the arm button on the remote control and keep it held on for 10 to 15 seconds, the unit should respond with an extended bleep.
Now let go of the arm button and then press the disarm button the unit should bleep twice to let you know that it is active but in a disarmed state. Let go of the tamper switch, should the unit activate then disarm it with the remote control. The unit is now ready for use and can be mounted on an outside wall.
Problem: Control Panel not arming system but the Remote will. Secondly check that the user code is not the default If this is the case it is possible that the system may have had a power cut, the backup batteries are old and depleted and consequently the system has lost its memory or at least part of. If this is the case, then the P1 jumper is incorrectly set to on inside the control panel next to the DC power socket. Once you have checked all the above and it hasn't corrected it - you will need to do a factory reset, as follows:.
Undo the Control Panel cover fixing screws and open the cover. Remove the DC power jack, then remove and disconnect one of the back-up batteries. Set jumper link P1 to the ON position. Reconnect the power supply jack. The Control Panel will now reconfigure itself with all factory default settings. Reconnect and replace the back-up battery.
Reset jumper link P1 into the OFF position. Close the Control Panel cover and refit the fixing screws. The system will now need setting up again, please refer to the manual - if you don't have access to one they can be downloaded from our ' Downloads ' section.
Suggested resolution: This indicates that there is no mains power or at least not enough coming from the PSU.
Check it's switched on, check the socket works with another appliance and finally if possible check the PSU with a multi-metre.
0コメント